DIY Bath Setup.
DIY Bath Setup.
Blog Article
We have encountered this article about A Step-by-Step Guide to Installing a Bathtub directly below on the web and believe it made sense to relate it with you in this article.
Installing a bathtub isn't exactly rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a moderately hard task. If the old bathtub is easily accessible, the task can relocate quickly; if you need to open up a wall to get rid of the old bathtub as well as position the brand-new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to move out the old tub and also embeded in the new one. Make sure you have actually qualified on your own for the task and fit trying it. Rather than employing a professional to take over a halfway-completed job, it is better to take into consideration utilizing one before you start. Chances are you might need a professional plumber to make tube links.
This short article will certainly assist you install a new bath tub in your shower room if you have currently purchased a new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your tools and also material checklist must make up the following:
Preparing for the Installment
First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is essential to make certain that if the tap includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets device to avoid pressure on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its final position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water. After doing so, turn on the taps to drain any water remaining in the system. The process of eliminating the existing taps can be rather troublesome as a result of the limited accessibility that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a cloth all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this process. When the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Before moving on to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Using the two wood boards under its feet, position the tub in the needed position. The wood boards are handy in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also readjusting the feet on the tub until the level checks out level.
To mount faucets, fit the bottom of the furthest adaptable tap connector to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply and also inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as also examine the overflow electrical outlet and the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the bathtub needs to wait up until the tub has actually been used at least when as this will resolve it right into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be connected to the tap finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a stiff seal, creating the water to penetrate the wall surface in between the bath and the tiling, causing difficulties with dampness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealer can fracture fairly early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the market. It is a good idea to fit the floor tiles making use of waterproof or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very taken with A Step-by-Step Guide to Installing a Bathtub and I really hope you enjoyed our blog posting. Those who enjoyed our blog entry plz be sure to share it. Thank you for taking the time to read it.
Learn More Report this page